Types of Compaction Equipment used on Construction

14 Types of Compaction Equipments In Construction

Compaction Equipment

Compaction is a process of improving or increasing the density of soil by a manual or mechanical method. It is employed to make the soil more stable and increase the bearing capacity of the soil layer on the construction site. There are different types of compaction equipment used on construction sites such as Smooth-Wheeled Rollers, Multi-tyre, Pneumatic-Tire Rollers, Heavy Pneumatic-Tyre Rollers, Sheep-foot Rollers, Tamping-foot Rollers Grid Rollers, etc.

Compaction equipment is often got by using a vibrating or non-vibrating steel drum roller, a pneumatic-tire roller, a grid or cleated roller, or a sheep-foot roller. Each is top-suited to specific applications.

Read More: Construction Equipment – 30 + Types of Equipment

Types of Compaction Equipment

The are different types of compaction equipment are as follows,

1. Smooth-Wheeled Rollers

Smooth-Wheeled Rollers
Smooth-Wheeled Rollers

It is used for the compaction of crushed rock, sand, gravel, and other granular materials. In general, they’re not suited to silts or clays but they can be used for the compaction of these materials.

The performance of smooth-wheeled rollers compaction equipment depends on the mass of the roller, width, and diameter of the rolls. Safety issues need to be considered when using these rollers on wet roads with cross-fall.

2. Multi-tyre, Pneumatic-Tire Rollers

Multi-tyre, Pneumatic-Tire Rollers
Pneumatic-Tire Rollers

This type of roller compaction equipment is usually self-propelled, with smooth tires on two axles in an offset arrangement, so that the wheels on one axle tracks are within the gaps between the wheels on the other axle.

The mass of the roller is often increased by attaching ballast, and therefore tire pressure is usually variable. Very thin soils with little or no cohesion, for example, silt, sandy silt, and clayey soil, compact well when using these rollers.

3. Heavy Pneumatic-Tyre Rollers

Heavy Pneumatic Roller
Heavy Pneumatic-Tyre Rollers

These rollers have four equally spaced independently suspended tires and should be ballast loaded up to an entire mass of fifty tonnes. They’re usually towed and are suitable for similar soils to the multi-tire pneumatic-tire rollers, also as for gravels and finer silts.

The difference between these and multi-tire pneumatic-tire rollers is that the heavy pneumatic-tire rollers can compact deeper layers, and therefore the surface density achieved is bigger.

4. Sheep-foot Rollers

Sheep-foot Roller
Sheep-foot Rollers

This type of roller is used for compacting fine-grained soils such as silty clays and heavy clays. They are generally used for the compaction of soils in dams, embankments, pavements, and railroad construction projects.

Sheepsfoot rollers compaction equipment also have two types static and vibratory. Vibratory types of rollers are for compaction of fine-grained soils and also soil with sand-gravel mixes. Generally, this type of roller is used for the compaction of subgrade layers of road and rail projects.

5. Tamping-foot Rollers

Tamping Roller
Tamping-foot Rollers

These are similar to sheep-foot rollers, although the legs are wider, shorter, and closer than the sheep’s feet. They are also often diamond-shaped.

These types of compaction equipment can be self-propelled or towed and will compress a wider range of soils than sheep-leg rollers, including silt and rock fragments, but not uniform sand.

Read More: What Is Surveying? 23 Different Types of Surveying Equipment

6. Grid Rollers

Grid Rollers- Compaction Equipment
Grid Rollers

The rolls on the grid rollers are usually made of a mesh of 20 mm diameter bars spaced 100 to 150 mm in both directions. Alternatively, they may be smooth drums with a pattern of square holes shaped into the surface.

They are mainly useful for scoria-type fills (random mixtures of large and small particles, usually angular and fairly soft). Their special use is in breaking oversized stones and forcing them under compact surfaces.

7. Vibratory Compactors

Vibratory Compactors
Vibratory Compactors

These rollers have a rotational unconventional weight to produce a vertical acceleration for the compaction of the material. They have different types of drums, such as smooth wheels and sheep-leg. The force applied to the soil is proportional to the acceleration in the vertical direction, so they have better performance than stationary rollers.

Vibrating rollers type compaction equipment is suitable for compacting non-adhesive clay, compacting from the base towards the surface, always leaving a layer of loose material on the surface.

8. Large Dual Vibrating Drum Rollers

Large Dual Vibrating Drum Rollers
14 Types of Compaction Equipments In Construction 17

Granular materials up to 250 mm can be successfully deposited with these rollers in four to 10 passes, provided that they are properly calibrated to obtain the most appropriate weight, frequency, and dimensions.

To complete condensation, it is usually necessary to operate the roller without vibration for two to four passes to strengthen the surface.

9. Earth Vibratory Compactors

Earth Vibratory Compactors
Earth Vibratory Compactors

These are typical of a large single vibratory drum type with large rubber equipment. They are generally used for difficult terrain and thick layers of earth.

Some rollers of this type are equipped with rubber-coated drums, which have been shown to be effective for the compaction of chips in chip seal manufacturing.

Read More: 75+ Construction Tools Name and Their Uses with Image

10. Powered Static Rollers

14 Types of Compaction Equipments In Construction
Powered Static Rollers

Static rollers are compact materials driven by pressure only. The thickness of a loose layer of material of 100 to 150 mm is compacted at any time, and a large number of passes are required to achieve full-depth condensation. These rollers are compact from top to bottom. Only the first 50 mm of material is usually narrower than the first four or five passes, and a further 20 or 30 passes may be necessary to complete condensation.

A major disadvantage in the use of these rollers is the crushing effect on the upper compressed material, which can produce highly fine materials, affecting the quality of the base course.

A variety of rollers are available, including tandem and three-steel wheels of 8 to 12-ton rollers, sheep-toes, and grid rollers used for bulk material compaction.

11. Track Rolling

Track Rolling
Track Rolling

Track rolling will produce an attractive surface finish, but it has a negligible condensation effect. Commonly used by forest road contractors for compact road and landing surfaces. However, tracks for construction equipment are designed for low ground pressure.

By definition, this means that tracked equipment is bad for condensation. Time and money spent tracking rolling will be invested in better-dedicated equipment. However, track rolling is probably better than nothing and can reduce surface scrap.

12. Power Rammer (Oscillating Foot Compactors)

14 Types of Compaction Equipments In Construction
Power Rammer

These small compactors, usually hand-operated, have relatively low output in terms of compact soil/hour volume. Typically, these compactors are used for compacting materials, which are used in an excavation in confined spaces, such as in trenches and around culverts.

Condensation of the material must be completed in layers using a power rammer. For granular soils, the layers should not be more than 230 mm thick, while for clinging soils, the layers should not be more than 1 mm thick. Power rumors have a vertical movement from 12 mm to 150 mm at a frequency of 20 to 200 blows per minute.

13. Vibrating Plate Compactors

Vibrating Plate Compactors
Vibrating Plate Compactors

These compacts are available in weights reaching from 50 to 150 kg and have an operating frequency of 400 to 10,000 vibrations per minute with reduced amplitude.

Vibration plate compactors are used to compress layers of 75 mm – 10 mm, the thickness of materials, and are ideal for small areas (up to 20 m), with 4–4 passes for the finest compaction required.

14. Single Drum Vibratory Rollers

Single Drum Vibratory Rollers
Single Drum Vibratory Rollers

These compactors are hand-operated and are ideal for granular materials with compact layer depths of up to 120 mm with four to six passes. They operate in high frequency, low amplitude mode.

You May Also Like:

Share This Post

Leave a Reply

Download Construction Excel Sheet

Scroll to Top
DMCA.com Protection Status