The Constructor

MARCH 25, 2012

Use of Precast Concrete in frames: There are two main types of precast building frame. The structural frame consists of slabs, beams and columns. Structural frames are mainly used for offices, car parks and retail developments. The cross-wall frame consists of floor slabs and solid walls.

Concrete 233

Concrete Foundation Maine Materials 233

The Constructor

NOVEMBER 8, 2011

Cracks in concrete beams due to increased shear stress 2. Cracks in concrete beams due to corrosion or insufficient concrete cover 3. Cracks parallel to main steel in case of corrosion in beams 4. Cracks due to increased bending stress in beams 5.

Concrete 244

Concrete Foundation Materials Contract 244

The Constructor

JANUARY 1, 2012

The benefits of using steel fibres in concrete are as follows: 1. Steel Fibres are generally distributed throughout a given cross section whereas reinforcing bars or wires are placed only where required 2. Steel fibres are relatively short and closely spaced as compared with countinuous reinforcing bars of wires.

Concrete 244

Concrete Foundation Materials Design 244

The Constructor

MARCH 21, 2012

The size of movement depends upon the change in temperature and the coefficient of thermal expansion o f concrete. The coefficient of thermal expansion of concrete is influenced largely by the coefficient of thermal expansion of the aggregates since the aggregate occupies 70-80% of the volume of the concrete.

Concrete 194

Concrete Foundation Contract Materials 194

The Constructor

MARCH 20, 2012

From the diagram above, we can see how the process unfolds. When the binding has set, the steel bars are placed into position.

Concrete 250

Concrete Foundation Materials Design 250

The Constructor

NOVEMBER 8, 2011

Cracks in reinforced concrete columns due to Steel Corrosion (cracks parallel to steel bars) 2. Cracks in reinforced concrete columns due to shrinkage of concrete 3. Cracks in reinforced concrete columns due to increased load on the slab 4. Cracks in reinforced concrete columns due to sulphate attack 5.

Concrete 223

Concrete Foundation Materials Contract 223

The Constructor

MARCH 20, 2012

Cleanliness: when repairing concrete, care must be taken to remove any dirt or dust that will prevent the repair concrete bonding with the parent concrete. Correct technique : The correct technique and the correct tools are essential for repairing damaged concrete.

Concrete 247

Concrete Portland Foundation Materials 247

The Constructor

NOVEMBER 8, 2011

Upon wetting, concrete tends to expand. This type of shrinkage is caused by the loss of moisture from the cement paste constituent, which can shrink by as much as 1% per unit length. Unfortunately, aggregate provides internal restraint that reduces the magnitude of this volume change to about 0.05%.

Concrete 229

Concrete Foundation Contract Materials 229

Construction Cost Estimating

MARCH 3, 2020

Work supervision, equipment utilization and construction procedures all must ensure the safety of the workers. Designers, planners, and engineers all must conform to well-established safety standards such as OSHA in order to ensure proper safety and security. Let us see now the various facets of Concrete Formwork.

Safety 52

Safety Concrete Plans Accidents 52

The Constructor

AUGUST 7, 2012

They may be load bearing, or they may be just decorative to act as a façade. The techniques that are used in the manufacture of panels permit a variety of finishes that imitate virtually any type of architecture at a fraction of the cost.

Concrete 190

Concrete Construction Foundation Materials 190

The Constructor

MARCH 21, 2012

in dry conditions), it should be suitable for use in concrete. Quality of Raw Materials: Cement: Provided the cement conforms with the appropriate standard and it has been stored correctly (i.e.

Concrete 230

Concrete Materials Foundation Design 230

The Constructor

AUGUST 7, 2012

In this case, the panels are designed and detailed by the engineer. Non-Load bearing cladding panel: A non-load bearing cladding panel must be designed, together with its fittings, to withstand the appropriate wind forces. The precast manufacturer checks the handling aspects and if necessary will modify the reinforcement accordingly.

Concrete 223

Concrete Foundation Maine Materials 223

The Constructor

NOVEMBER 21, 2011

Both the rate and degree of hydration, and the resulting strength of the final concrete, depend on the curing process that follows placing and consolidating the plastic concrete. This reaction, called hydration, produces a stone-like substance—the hardened cement paste.

Concrete 189

Concrete Foundation Materials Design 189

The Constructor

NOVEMBER 28, 2011

This method is used where large quantity of concrete work is involved at greater height, where other means of transporting is not easy to do. Concrete pumps have been known for more than 50 years.

Concrete 240

Concrete Transportation Foundation Design 240

The Constructor

AUGUST 10, 2012

These are the environments to which the concrete will be exposed during its working life. These are: Mild exposure Moderate exposure Severe exposure Very severe exposure, and Extreme exposure. The durability requirement, like clear cover to reinforcement steel is governed by these exposure conditions.

Concrete 181

Concrete Foundation Environment Materials 181

CivilJungle

JANUARY 29, 2022

What Is Cast-In-Situ Concrete? Cast-in-situ concrete is prepared, placed, and finished on the construction site. Another name of cast-in-situ concrete is poured-in-place concrete. Generally, concrete slabs, concrete foundations , beam, column, wall, roof, etc., Definition of Cast in Place Concrete.

Concrete 52

Concrete Foundation Site Materials 52

The Constructor

NOVEMBER 25, 2011

WHY WE TEST CONCRETE SRTRENGTH AFTER 28 DAYS? WHY WE TEST CONCRETE SRTRENGTH AFTER 28 DAYS? Tweet Why do we test concrete compressive strength after 28 days? The table below shows the compressive strength gained by concrete after 1, 3, 7, 14 and 28 days with respect to the grade of concrete we use.

Concrete 250

Concrete Foundation Materials Design 250

The Constructor

NOVEMBER 22, 2011

It has many advantages when compared to the normal conventional concrete. Fly ash is considered as one of the waste industrial product that cannot be easily disposed. It solves the problem of disposal of flyash and at the same time it reduces the cost of the construction.

Concrete 224

Concrete Foundation Materials Design 224

The Constructor

MARCH 25, 2012

There is no grout loss, such as that from badly fitting formwork, which results in poor quality concrete like shown below. By careful selection of materials and finishing processes, a wide range of high quality finishes can be obtained.

Concrete 171

Concrete Foundation Materials Design 171

The Constructor

MARCH 23, 2012

There are two ways of overcoming this problem: Embed another material in the concrete which is strong in tension – reinforced concrete Remove the tension altogether – by arching or prestressing.

Concrete 133

Concrete Foundation Materials Comparison 133

The Constructor

MARCH 22, 2012

Following are the cases, which affect creep in concrete: When the aggregate volume is increased, creep will be less as the aggregate is more rigid than the cement paste. Creep can continue over a long period of time (more than 30 years in some cases) after the application of the load.

Concrete 141

Concrete Foundation Materials Contract 141

The Constructor

MARCH 25, 2012

The following figures illustrate the precast concrete process: 1. The individual components are prefabricated off site then taken to site where they are erected.

Concrete 143

Concrete Foundation Materials Design 143

The Constructor

MARCH 25, 2012

WHAT IS PRECAST CONCRETE? Tweet Precast concrete is cast under factory controlled conditions and not erected on site until it is fully hardened. Tweet Precast concrete is cast under factory controlled conditions and not erected on site until it is fully hardened.

Concrete 130

Concrete Foundation Materials Contract 130

The Constructor

AUGUST 18, 2012

Related posts: SELF COMPACTING CONCRETE WITH TESTS TESTS ON HARDENED CONCRETE CHEMICAL TESTS ON CONCRETE STRUCTURES COMMON TESTS ON THE FRESH CONCRETE Removing concrete slab to build wood deck but worried about water entering basement? Tweet Loading GET LATEST TOPICS IN YOUR EMAIL- SUBSCRIBE NOW.

Concrete 139

Concrete Foundation Materials Contract 139

The Constructor

NOVEMBER 17, 2011

The shells are most commonly flat plates and domes , but may also take the form of ellipsoids or cylindrical sections, or some combination thereof.

Concrete 212

Concrete Foundation Materials Design 212

The Constructor

DECEMBER 17, 2011

It is new technique involved in the civil engineering.Reactive powder concrete in made by replacing the conventional sand and aggregate by grounded quartz less than300 micron size, silica fume, synthesized precipitated silica ,steel fibers about 1 cm in length and 180 micron in diameter.

Concrete 161

Concrete Portland Foundation Materials 161

The Constructor

AUGUST 24, 2012

Heat expansion of the cladding panel must be allowed for in the design. But considerations must also be given to loads that may be exerted on the cladding due to either its own or the supporting structure’s expansion during fire. Thus: Firstly the fixings must be flexible enough to allow for two dimensional movement.

Concrete 127

Concrete Foundation Materials Contract 127

The Constructor

JANUARY 22, 2012

The stress strain curve of concrete lies between those of the aggregate and the cement paste. The aggregate is more rigid than the cement paste and will therefore deform less (i.e. have a lower strain) under the same applied stress. However this relationship is non-linear over the most of the range.

Concrete 137

Concrete Foundation Materials Contract 137

The Constructor

NOVEMBER 28, 2011

Procedure for measuring bulk density of concrete is as per IS 1199 – methods of sampling and analysis of concrete. The steps are as follows: i)Take freshly mixed concrete from transit mixer by using wheel borrow. ii) Fill the cylindrical measure with concrete as soon as practicable after mixing.

Concrete 133

Concrete Foundation Materials Design 133

The Constructor

NOVEMBER 21, 2011

The concrete can be specified in two ways : a) by proportioning of the constituents /ingredients (nominal mix) b) by required strength (Design mix) Concrete is mixed by any two methods, based on requirement as per quality and quantity of concrete required.

Concrete 122

Concrete Foundation Materials Design 122

CivilJungle

MAY 12, 2020

What Is a Concrete Surface Retarder? Surface retarders, also know surface “deactivators,” are applied to fresh concrete to chemically delay the set of the surface mortar. Unlike concrete set retarders, they allow the rest of the concrete to cure normally , without affecting the setting rate or strength gain.

Concrete 52

Concrete Foundation Compensation Inspections 52

Construction Equipment

MARCH 18, 2021

Updates to the StructureScan Mini XT all-in-one GPR concrete inspection system include a software update and a newly designed survey wheel for the Palm XT Antenna. The product is designed for locating rebar, conduits, post-tension cables, and voids. The Mini XT also can help identify structural…

Inspections 62

Inspections Software Software Concrete 62

Construction Cost Estimating

AUGUST 13, 2019

The safety of workers and the public is mainly dependent on the construction work supervision, equipment deployment practices, and construction method used. Formwork designers, project planners, and managers should abide by the requirements of relevant standards like OSHA regulation with the purpose of providing good safety planning.

Concrete 40

Concrete Site Safety OSHA 40

CivilJungle

APRIL 22, 2022

What to Do If the Concrete Cube Fails After 28 Days? So, What To Do If Concrete Cube Falls after 24 days? There are many record and recovery choices if the concrete cell falls in the Test. There are many record and recovery choices if the concrete cell falls in the Test. Cube Test of Concrete.

Concrete 52

Concrete Modeling Overhead Documentation 52

The Constructor

NOVEMBER 15, 2011

All of these elements are used by interior designers to develop a functional, safe, and aesthetically pleasing space for a building’s user. The work of an interior designer draws upon many disciplines including environmental psychology, architecture, product design, and traditional decoration (aesthetics and cosmetics).

Software 114

Software Software Design Concrete 114

PC Construction

OCTOBER 13, 2023

Preconstruction on this design-build project began two years ago to upgrade the existing filter complex and replace the aging Leopold filter underdrain system. PC focused on isolating the construction of the affected filter from the others in operation by building full enclosures that were inspected and maintained on a daily basis.

Florida 88

Florida Permits Inspections Procurement 88

The Constructor

MARCH 19, 2012

When concrete is fresh and in its liquid state it must be restrained within a mould in order for it to set in its required shape. A smooth outer surface provides the main support for the concrete as it sets. Formwork is the term used to describe this mould. For most in-situ pours, the formwork is made of wood.

Concrete 223

Concrete Foundation Materials Design 223