Revit OpEd

SEPTEMBER 12, 2012

Daryl wrote on Monday that the concept of View Discipline isnt documented well. Software documentation tends to be a bit dry, too often a very literal, "Un-checking this turns the feature off". It was meant to make it simple to alter the appearance of our model to be more in sync with what a structural engineer wants to see.

Revit 55

Revit Architecture Autodesk Plans 55

Building Information Management

JULY 2, 2012

Open information exchange of Heating, Ventilating and Cooling systems (HVACie), released by the Engineer Research and Development Center for public review. Accompanying the technical documentation are instructions for creating the HVACie files using commercial design software. 2012-03-01-CERL-CR-12-2-ModelView. Table of Contents.

Documentation 40

Documentation Equipment Modeling Design 40

Building Information Management

JULY 2, 2012

Open information exchange of Heating, Ventilating and Cooling systems (HVACie), released by the Engineer Research and Development Center for public review. Accompanying the technical documentation are instructions for creating the HVACie files using commercial design software. 2012-03-01-CERL-CR-12-2-ModelView. Table of Contents.

Documentation 40

Documentation Equipment Modeling Design 40

ProcurementExpress.com

NOVEMBER 30, 2016

A proven way to find good contractors to add to your bid list, is to ask design consultants to refer contractors with whom they have worked with on successful projects. The structural engineer who designed the building was asked if the dishes could be put on this roof/floor area. Improper planning. Contractor default problems.

Risk 40

Risk Construction Plans Structural Engineering 40

Building Information Management

JULY 20, 2012

The clearance zones for the accessible WC package are based on documents such as BS 6465: Part 2 Sanitary installations and Approved Document M of the Building Regulations (E&W). In many cases installation information is a reference to NBS workmanship clauses or the manufacturer’s installation guide.

BIM 40

BIM Zoning Modeling Products 40

Rory Woolsey

MAY 31, 2012

Note that for budgetary estimating many unit price and assemblies cost data reference books start at this same “bare” point when making reference to “including overhead and profit.” ” This typically refers to the installing contractors overhead and profit or more likely, the subcontractor unit cost.

Estimating 40

Estimating Overhead Profitability Construction 40

Building Information Management

NOVEMBER 18, 2014

This argument is hard to convince owners and contractors as they expect the documents you provide as part of your service to contain enough information for your design to be fully realised. Traditionally only drawings and written material were provided to others, which they referred to but didn’t directly use to generate their work.

BIM 40

BIM Modeling Drawings Agreement 40

Autodesk Construction Cloud

JANUARY 6, 2022

Usually, this is referring to diversity in terms of background , ethnicity, age, and experience. Now, architects and structural engineers are working side by side with the general contractor. However, inclusivity is also essential when it comes to access to information. At all steps of the way, communication must be prioritized.

Construction 52

Construction Estimating Design Budgeting 52

CivilJungle

OCTOBER 18, 2021

Then after architect consult with a structural engineer and MEP engineer for details of the reinforcements and other detail for use, how deep your foundation will be, the size of gravel to be used, column width, electrical, plumbing, etc. Following are the list of document project required before applying for permission.

Construction 98

Construction Foundation Electrical Drawings 98

BIM & Beam

AUGUST 1, 2018

This is the third blog post in a series that discusses the advantages of working on concrete projects in a BIM process for structural engineers. Segmentation is dictated by engineering, architectural, or fabrication requirements, and its reinforcement is determined by the structural engineer.

Modeling 75

Modeling BIM Concrete Design 75

Revit OpEd

APRIL 14, 2016

BIG STUFF New Features Videos - Start with these videos provided as part of the help documentation if you prefer watching videos to reading my blog post. Reference Planes - We can now create different Reference Plane sub-categories which can be given different graphic properties. has finally been tackled.

Revit 40

Revit Fabrication Schedule Modeling 40

Job Order Contracting

JANUARY 13, 2017

Common construction abbreviations as as part of cost estimating software, Job Order Contracting software, and construction documents is a standard practice. REF: Refer, Reference, Refrigerator. SCFT: Structural Clay Facing Tile. SE: Structural Engineer. Do not use spaces within an abbreviation.

Construction 100

Construction Concrete Electrical Fabrication 100

Autodesk Construction Cloud

NOVEMBER 2, 2021

Giana started her career in civil and structural engineering, working on both domestic and international programs. For ten years she delivered significant projects, proving her construction prowess and gaining experience across the engineering and construction industry. Christian Paul. Senior Project Manager. Atlanta, Georgia.

Construction 52

Construction BIM San Francisco Management 52